Langfang Dehou Wood Industry Co., Ltd.
Products  /  Plywood Sheathing for Roof
Yufu

Plywood Sheathing for Roof

Yufu plywood sheathing for roof decks: phenolic exterior glue, sealed edges, T&G joints and printed nail lines. Built for rain delays, snow loads and crew traffic, in 12, 15 and 18 mm.

$ Request Quote

Yufu · Roof Deck Plywood

Plywood Sheathing for Roof

Made for one job: the roof deck. Built for weeks open to rain before shingling, then snow, wind and foot traffic. Exterior-bond glue, sealed edges, tongue-and-groove joints and printed nailing lines are available; thickness and edge style can be tailored.

Request a Quote →
Sheet Size 2440 × 1220 mm
Thickness Range 12 / 15 / 18 mm
Thickness Tolerance ±0.5 mm
Length and Width Tolerance ±3 mm
Warp ≤ 1%
Moisture Content 6–12%
Rafter Spacing Guide 12 mm up to about 400 mm; 15–18 mm up to about 600 mm
Options Thickness, edge, marking and face adjustable

Why Roof Crews Specify Yufu

01

Exterior Phenolic Glue

Glue lines stay bonded through repeated wet-dry cycles while the roof waits for its covering.

02

Tongue-and-Groove Joints

T&G locks sheets and supports edges between rafters, with no clips. Square-edge also available.

03

Load-Conscious Build

Thickness set by rafter spacing and local snow and wind load; stiff enough for nail guns and bundles.

04

Roof Diaphragm Support

Helps transfer lateral forces from wind and seismic activity to the building's structural framework.

Roofs Where This Deck Panel Fits

Asphalt Shingle and Clay Tile Roofs: Flat, stable base that carries the covering.
Low-Slope Membrane Roofs: Smooth deck with firm joints; membranes show every gap.
Reroofing and Replacement: Replace damaged sections without disturbing sound areas.
Carports and Outbuildings: Weather-ready decks for garages, sheds and carports.
The spacing guide is a starting point. Confirm thickness against local code, snow load and wind load.

Plywood vs OSB on a Roof Deck

On roofs the difference shows up in exposure and edge behaviour.

  • Long Exposure: Plywood dries faster and swells less at the edges, suiting rain delays
  • Shingle Appearance: Less edge swelling avoids ridging under shingles and thin membranes
  • Fastener Holding: Holds nails well near the edge, where uplift concentrates
  • Budget: OSB is often cheaper, suiting dry-season jobs with short exposure
Before you order, share: rafter or truss spacing and roof pitch; local snow and wind loads; roof covering and how long the deck may stay exposed. Yufu will recommend thickness, edge profile and marking layout.

Why Choose Yufu?

Langfang Dehou Wood Industry Co., Ltd., established in 2016, specializes in construction formwork plywood.

  • Experience: Years of plywood production.
  • Capacity: About 50,000 m³ per year.
  • Equipment: Veneer processing, pressing, cutting, surface treatment.
  • Technology: Multiple utility model patents.
  • Bulk Supply: Ready for wholesale and project orders.

Frequently Asked Questions

How much expansion gap between sheets?

About 3 mm at edges and ends, including end joints on T&G edges.

Can sheathing be left exposed to rain?

Briefly. Cover with underlayment soon, and let soaked panels dry first to avoid trapped moisture and cupping.

How should fixing change near eaves, ridges and gables?

Ring-shank nails about 50 mm, roughly 150 mm apart on supported edges and 300 mm in the field; tighten spacing in high-uplift zones per local code.

How do I know if old sheathing needs replacing?

Spongy spots, dark staining, sagging between rafters or daylight from the attic. Replace rather than shingle over.

Which direction should sheets run?

Long side across rafters, end joints staggered by at least one rafter spacing, every end on framing.

Request a quote

Tell us the size, thickness, quantity and destination port. We reply with a mill-direct price, lead time and loading plan.

Get a Quote WhatsApp